※萬向節注意事項：
1調整時不能超過規定的角度15度
2如超過此極限心軸易磨損或斷裂
3工作時應經常加潤滑油脂
※Note of cardan Joint
1.Do not set the angle to more than the specifled l5 degrees.
2.If the limit is exceeded，the shaft will be easy to wear or break.
3.During work，lubrication should be added frequently.
注：ER8和C5最小間距為13，ER11和C6最小間距為18，ER16和C9最小間距為26，ER20和C12最小間距為28
|
SU100×165 |
SU120×200 |
SU120×300 |
SU160×450 |
SU220×360 |
SU250×500 |
SU170X200 |
SU300X400 |
SU400X550 |
SU450X550 |
SU150X800 |
SU300X1000 |
|
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
ER8/5 ERll/7 ERl6/10 ER20/13 C5/5 C6/6 C9/9 C12/12 |
|
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
1∶1 1∶2 |
|
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
13 18 26 28 |
|
100×165 |
120×200 |
120×300 |
160×450 |
220×360 |
250×500 |
170×200 |
300×400 |
400×550 |
450×550 |
150×800 |
300×1000 |
|
2-8 |
2-12 |
4-16 |
4-16 |
6-14 |
4-18 |
2-12 |
4-16 |
4-18 |
4-18 |
4-18 |
4-18 |
掃一掃
QQ咨詢